Application Analysis of Calcium Carbonate Rotary Vibrating Screen

The sealing performance of calcium carbonate rotary vibrating screen is pretty good, non-blocking design and precise screening. Besides, you can also choose ultrasonic vibrating screen instead of common rotary vibrating screen in order to achieve more accurate screening performance, the screening accuracy even can reach 500 mesh.

 In the process of production of calcium carbonate, it mainly includes light calcium carbonate and heavy calcium carbonate, the production process of two kinds of calcium carbonate is the same during crushing and screening. When screening the calcium carbonate, the output rate is designed according to manufacturing production rate per hour, the screening amount is calculated as per the material amount after crushing, the general selection of material granularity is around 100 mesh and the main selection specification is 60 mesh, 80 mesh and 120 mesh etc. In addition, the mesh size is also selected according to the needs of users. In the process of screening, rotary vibrating screen is the best screening equipment, the screen mesh can be replaced with the previous required mesh size in order to achieve the screening requirements.

Notes of Ultrasonic Vibrating Screen before Using

Ultrasonic vibrating screen is a new sieving equipment compared with rotary vibrating screen, now PK Machinery will introduce the notes before using in details.

1.The input voltage of ultrasonic vibrating screen power supply is AC 220 V, ultrasonic power output is led by case back panel connection box, the red one is "+".When wiring, please pay attention to the voltage polarity, wrong wiring is not allowed.

2.In the condition of meeting the production requirements, lower power grade is better. Maximum current shouldn’t exceed 0.4.

3.When net rack is without load (the net rack is no tension), please do not start up the ultrasonic generator, otherwise it will cause overflow of power and damage of net rack and the oscillator.

4.Screen mesh must be tight, otherwise it will affect the ultrasonic output and the effect of vibration.

5.Oscillator aviation plug docking screws must be tightened and wrapped with insulating tape well, thus it will prevent dust .During operation, please pay attention to protect the connector.

6.Check whether the screw nut of oscillator and cable plug nut is tightened well or not before using, as well as the screw nut of oscillator and the net rack. In process of operation, pay attention to the protection of case and oscillator cables, cables and oscillator socket should be anti-moisture ,no water is allowed to enter in the connection plug and socket.

7.If the material is conductive, please extend the ultrasonic wire, stay the ultrasonic resonance power away from the screening site in order to prevent the material into the power case causing short-circuit.

8. When replace the screen mesh, scraping the residual gum of inner ring (resonance loop) with a sharp wallpaper knife, please do not grind by grinder wheel in order to prevent damage of resonance loop.

9.Each unit of ultrasonic generator includes a resonant power supply, an oscillator and a net rack. Please recognize each part clearly and don't mix with other ultrasonic generator.

How to Solve Rotary Vibrating Screen Clamp Gets Hot and Current Rises Problems?

Rotary vibrating screen model:XZS-1500-3
Screening material: calcium carbonate
Mesh size: mesh#100, mesh#200 and mesh#325.


Customer :The stainless clamps is very hot. Especially in the screen mesh 325. We were forced to stop the operation. What can you suggest we will do?

PK Machinery: You said the stainless clamps is very hot, normally it is caused by bolt looseness of clamp, please tighten the bolt of the clamp.

 

Customer: When it is loaded with the material for screening, the current will rise from 7.5amperes to 15 amperes. It even rises to 30 amperes and the circuit breaker of 15 amp broke. How much current reading is the normal operation?

PK Machinery: Please check whether the power wires and grounding wires are well connected or not .
Concerning the current rising, normally, current rises when the machine starts to run for seconds, it will become normal later soon.


Customer: We tried to work on the machine. Tighten the clamps, and check on the wires. Its is doing well. Thanks very much!

What Shall We do to Solve Slow Material Discharging of Rotary Vibrating Screen ?

when we handle material in our daily life, we may encounter such situation : material discharging is slow. It may cause by the reasons as following aspects:
1. Check whether the screen mesh cloth and impurity removal is level or not, or if it is over height, normally it should be higher than about 5 mm, the discharging outlet design is different according to different material types.

2.During operation, check the screen mesh surface or if the discharging outlets are in the level, this has direct relation to the sieving effect. If it is not level, please adjust timely. Rotary vibrating screen is equipped with supporting foundation bolt before leaving factory, customers can adjust the rotary vibrating screen in the level and lower it properly by adjusting the foundation bolt.

3.Besides, the key point is to adjust vibration motor upper and lower eccentric block angle, smaller angle can make the material distribute and spread outwards fast, on the contrary, larger angle will make it slow .Adjustment of the eccentric block vibration motor angle should be around 5 degrees, if you have strict requirements on screening accuracy, the angle should not be too small, otherwise the material will spread outward quickly which is not good to the screening effect. Usually ,the angle of rotary vibrating screen motor upper and lower eccentric block angle is 45 ° before leaving factory.